设为首页    收藏本站

华彩光电首页
      产品列表
排水沟模具
排水渠模具
流水渠模具
排水槽模具
流水槽模具
配重块模具
拉盘模具
方涵模具
围墙板模具
流水槽钢模具
      资质荣誉
      联系我们
保定乐丰流水槽模具厂
地址:保定市城东工业区
电话:18831266588
传真:0312-8103818
邮箱:107108222@qq.com
行业新闻

流水槽钢模具的使用步骤及脱模程序

[关闭该页][设为首页][添加收藏][发送朋友][打印][ ]

流水槽钢模具主要用于电缆沟、排水沟、水利渠道的铺设,流水槽钢模具设计合理。用于水利建设非常合适.流水槽是为减免山洪及泥石流危害,修筑在荒溪冲积扇或侵蚀沟口的排导措施,主要包括导流堤、流水槽和束流堤三个部分。导流堤与束流堤组成束导堤,以防止泥石流漫流改道危害。在公路工程中,流水槽常被建在坡路两边,用来排水以及达到减缓水流速度的目的,对公路路基起到很大的保护作用。

The flow channel steel mould is mainly used for laying cable trench, drainage ditch and water conservancy channel, and the design of the flow channel steel mould is reasonable. It is very suitable for water conservancy construction. Flume is a drainage measure built at the mouth of alluvial fan or erosion gully of waste stream to reduce the hazards of mountain flood and debris flow. It mainly includes diversion dike, flume and beam dike. The diversion dike and beam dike form a beam guide dike to prevent the hazard of debris flow diversion. In the highway engineering, the flume is often built on both sides of the slope road to drain water and slow down the flow speed, which plays a great role in protecting the highway subgrade.

流水槽钢模具首先在预制之前要对模具进行检查,看模具的内部是否光滑,用抛光机打磨光滑,这样就能够防止脱模过程中,混凝土预制件脱不下来。然后再对排水沟模具进行刷油,这其中也有要注意的地方。一般工地上都是使用废机油,而废机油颜色灰暗,而且基友能够渗透到混凝土中去,从而影响预制构件的美观性,所以我们提倡使用食用油,不渗透,光滑度高。第三道工序是装混凝土,对流水槽钢模具整体进行振捣,可以使用振捣棒,在这过程中,一定要将混凝土振捣均匀,不然将来预制出来的构件会有气孔。最后就是预制件的脱模工序了,为了能够让模具在下次使用时地心应手,我们还得将模具清理干净。

Before prefabrication, the flow channel steel mould shall be checked to see whether the inner part of the mould is smooth and polished with a polishing machine, so as to prevent the precast concrete parts from falling off during the demoulding process. Then brush the drain mould with oil, which also needs attention. Generally, waste oil is used on the construction site, and the color of waste oil is gray, and the basic friends can penetrate into the concrete, thus affecting the aesthetics of prefabricated components. Therefore, we advocate the use of edible oil, which is impermeable and has high smoothness. The third process is to install concrete and vibrate the whole flow channel steel mould. The vibrator can be used. In this process, the concrete must be vibrated evenly, otherwise the prefabricated components will have air holes in the future. Finally, it is the demoulding process of the prefabricated parts. In order to make the mold handy in the next use, we have to clean the mold.


【上一个】 排水沟模具的操作规范介绍 【下一个】 排水沟模具的使用步骤


 · 流水槽钢模具的使用步骤及脱模程序 · 流水槽钢模具的发展顺应了市场
 · 流水槽钢模具行业不断推陈出新 · 流水槽钢模具企业之间需要通力合作
 · 流水槽钢模具为我国的隔震实验工程点赞 · 流水槽钢模具的市场前景
 · 流水槽钢模具与新农村建设发展相辅相成 · 流水槽钢模具购买时的注意事项

水槽模具,排水槽模具,流水槽模具-保定乐丰流水槽钢模具厂 |护坡砖模具|沟盖板模具|隔离墩模具|排水沟模具 |排水沟模具